This blog shows you how to replace the stock oem high&low beam front turn signal license plate light and back up light with LED bulbs on a 2020 Kia Telluride. These LED turn signal lights are built-in load resistor, anti hyper flash, error free, much brighter than OEM halogen bulbs, its simple installation process can save you time and make you have better upgrading experience.
Kia Telluride LED Replacement List
High&Low Beam: LAplus 9005
(Stock halogen bulb size: 9005) 9005 is a common bulb size for headlights. In this blog we will use Lasfit LAplus series 9005 to show the installation. They are built without an external driver directly plug and play. New cooling system with a unique ball-bearing fan for heat dissipation, and upgraded LED clip to ensure ultra-high luminous efficiency.
Front Turn Signal Light: T-1157A
(Stock halogen bulb size: 1157) 28W/bulb, 2600LM/bulb. CANBUS system can prevent 95% hyper flash and error warning. No need to add extra resistors or parts anymore. They are designed to directly plug and play. Depending on the position and function, you should choose amber for front turn signal lights.
License Plate Light: L-T10
(Stock halogen bulb size: 168) 800LM/set, much brighter than OEM halogen bulbs. It's necessary and easy to achieve to add a modern appearance to your truck by replacing stock halogen bulbs with this interior LED bulbs.
Back Up Light: T-T15
(Stock halogen bulb size: 921) 3000LM/set, bright white or brilliant red. CANBUS support for error-free. Built-in intelligent temperature control system. 100% plug-and-play installation can be completed in about 5 minutes on most vehicles.
Kia Telluride LED Replacement Process
Installation of High&Low Beam
Picture1: Lasfit LAplus 9005
Picture2: Remove the dust cover.
Picture3: Twist out the stock headlight bulb.
Picture3: Unplug the halogen bulb by releasing the clip on the connector.
Picture4: Comparison between original halogen headlights and LAplus 9005.
Picture5: Connect the power plug.
Picture6: If it does not work, turn around the plug and connect the plug again.
Picture7: Align to the headlight housing socket, and lock it in place.
Picture8: There is desiccant in the OEM dust cover which hits the LED bulb cooling fan, use screw driver to move the fan out.
Picture9: Put the cover dusk back.
Picture10: Comparison between halogen headlights and LED headlight.
Picture11: Comparison between halogen headlights and LED headlight—Low Beam.
Picture12: Comparison between halogen headlights and LED headlight—High Beam.
Installaiton of front turn signal light
Picture1: Lasfit T-1157A
Picture2: Twist out the stock turn signal light from the housing.
Picture3: Slightly press the bulb, then twist it out.
Picture4: Put the LED bulb into the socket, slightly press the bulb, then lock it.
Picture5: Put the LED bulb into the socket, slightly press the bulb, then lock it.
Installation of License Plate Light
Picture1: Lasfit L-T10
Picture2: Use the screwdriver to remove the screw, and take out the whole plastic unit.
Picture3: Remove the socket from the vehicle body.
Picture4: Twist the stock halogen bulb.
Picture5: Take out the halogen bulb.
Picture6: Plug in the LED bulb T10.
Picture7: Test if the installed LED lights work.
Picture8: Reinstall the license plate light and fix it with the screw.
Picture9: Comparison between halogen headlights and LED headlight.
Installaiton of Back Up Light
Picture1: Lasfit T-T15
Picture2: The back up light installation is a little complicated, we need to remove the whole plastic cover to reach the back up light.
Picture2: Remove the little cover on the handle.
Picture3: Use the screwdriver to remove two screws.
Picture4: Use the removal panel tool kit to pry the cover.
Picture5: Pay attention to the buckle and do not break it.
Picture6: Remove the two side covers before removing the car rear cover.
Picture7: Here is the back up light.
Picture8: Twist out the stock back up light.
Picture9: Take out the halogen bulb.
Picture10: Lasfit's designed LED bulbs are the same size as halogen bulbs, so there won't be any installation issues.
Picture11: Put the car in reverse to test if the bulb works.
Picture12: Put the LED back in the socket and lock it in the place.
Picture13: Replace the halogen back up light on the other side.
Picture14: Reinstall the plastic cover and fix them with all screws.
Picture15: Comparison between halogen headlights and LED headlight.
We hope this article has provided you with a clearer understanding of our products and how they can enhance your driving experience. If you have any questions about our products or the installation process, please don't hesitate to reach out to us. We're always happy to assist you and ensure that you have a smooth and enjoyable experience with Lasfit's products.
